Refrigerator fit checker

Will your fridge
clear the wall?

Compare the right-door swing of 20 LG and Samsung French-door refrigerators against your own kitchen measurements.

Door swing planTop view
Full wall beside the open doorLayout only

Measure from the fridge body to the wall. Try ¼″ or 6.35 mm.

Where does the right wall end?

The wall extends past the hinge, alongside the fully open door and handle.

Model comparison

¼″ · Full wall

How we check these clearances · Checking drawer access?

LG and Samsung refrigerator wall-clearance comparison
RefrigeratorRight-side verdictClearance at your settingSource
LGLF25Z6211SClears 90°Meets the 5/32″ allowance with 3/32″ to spare.
Model notes

The model-specific Pro Builder sheet lists 5/32″ at the door edge with its pocket handle. Use the supplied side spacers in a narrow opening.

LGLF24Z6530SWon’t fitDoor or handle hits the wall. Its swing needs at least 2⅛″.
Model notes

LG lists 5/32″ beside the cabinet and 2⅛″ beside the open door with its bar handle. Use the supplied side spacers in a narrow opening.

SamsungRF70H25GERAAWon’t fitDoor or handle hits the wall. Its swing needs at least 44 mm (about 1¾″).
Model notes

Samsung draws ¼″ from the case to a short cabinet side. A long wall reaches the bar handle, which projects about 1¾″ (44 mm) at 90°. V7 allows 3¾″ beside a wall. V10 leaves the intermediate range unconfirmed.

SamsungRF70H25HERAAWon’t fitDoor or handle hits the wall. Its swing needs at least 44 mm (about 1¾″).
Model notes

Samsung draws ¼″ from the case to a short cabinet side. A long wall reaches the bar handle, which projects about 1¾″ (44 mm) at 90°. V7 allows 3¾″ beside a wall. V10 leaves the intermediate range unconfirmed.

LGLF24Z6330SNeeds dataThe right-side swing dimension with the original handle is missing. Overall open-door width cannot confirm this gap.
Model notes

The shared installation drawing shows 5/32″ for a short side wall. The sheet gives overall open-door width but omits a right-side dimension with the bar handle.

LGLY24Z6231VNeeds dataThe right-side swing dimension with the original handle is missing. Overall open-door width cannot confirm this gap.
Model notes

The shared installation drawing shows 5/32″ for a short side wall. The model sheet has conflicting open-door dimensions and no confirmed right-side measurement for a long wall.

LGLRFLC2706SWon’t fitDoor or handle hits the wall. Its swing needs at least 4½″.
Model notes

LG lists 4½″ at the open door edge with its handle. The sheet gives no smaller verified 90° gap for a wall ending at the hinge.

LGLRFXC2606SWon’t fitDoor or handle hits the wall. Its swing needs at least 4¼″.
Model notes

LG lists 4¼″ at the open door edge with its handle. The sheet gives no smaller verified 90° gap for a wall ending at the hinge.

LGLF29H8330SWon’t fitDoor or handle hits the wall. Its swing needs at least 4¼″.
Model notes

LG lists 4¼″ with its original bar handle. The 2¼″ handle-off dimension applies only with the handle removed.

LGLF25G8330SWon’t fitDoor or handle hits the wall. Its swing needs at least 4¼″.
Model notes

LG lists 4¼″ with its original bar handle. The 2¼″ handle-off dimension applies only with the handle removed.

LGLRFLS3206SWon’t fitDoor or handle hits the wall. Its swing needs at least 4¼″.
Model notes

LG lists 4¼″ at the open door edge with its handle. The sheet gives no smaller verified 90° gap for a wall ending at the hinge.

LGLF30S8210SWon’t fitDoor or handle hits the wall. Its swing needs at least 2⅜″.
Model notes

LG Customer Care specifies 2⅜″ for either door to reach 90°. The product sheet gives only the combined two-door width.

SamsungRF70H30GERAAWon’t fitDoor or handle hits the wall. Its swing needs at least 44 mm (about 1¾″).
Model notes

Samsung draws ¼″ from the case to a short cabinet side. A long wall reaches the bar handle, which projects about 1¾″ (44 mm) at 90°. V7 allows 3¾″ beside a wall. V10 leaves the intermediate range unconfirmed.

SamsungRF70H30HERAAWon’t fitDoor or handle hits the wall. Its swing needs at least 44 mm (about 1¾″).
Model notes

Samsung draws ¼″ from the case to a short cabinet side. A long wall reaches the bar handle, which projects about 1¾″ (44 mm) at 90°. V7 specifies 3¾″ for 90°. Between the handle outline and that allowance, check the installation.

SamsungRF70F23DERAAWon’t fitDoor or handle hits the wall. Its swing needs at least 2⅛″.
Model notes

The 90° plan shows a 2⅛″ door projection. Samsung calls for 3¾″ along a wall. A tighter short-wall fit needs hinge-setback data.

SamsungRF23DB960012AAWon’t fitDoor or handle hits the wall. Its swing needs at least 2¼″.
Model notes

The drawing shows a 2¼″ door projection. The spec sheet calls for 2½″ alongside a wall; the fit guide allows 3¾″ for 90°. A tighter short-wall fit needs hinge-setback data.

SamsungRF24BB6200QLAAWon’t fitDoor or handle hits the wall. Its swing needs at least 2⅛″.
Model notes

The 90° door outline extends 2⅛″. The fit guide gives this model 3¾″ along a wall on its second page. A tighter short-wall fit needs hinge-setback data.

SamsungRF27CG5100SRAAWon’t fitDoor or handle hits the wall. Its swing needs at least 1⅞″.
Model notes

The door alone projects 1⅞″. The fit guide says 3¾″, while the drawing shows 4¼″ to the handle. The larger dimension clears both. A tighter short-wall fit needs hinge-setback data.

SamsungRF29BB8600QLAAWon’t fitDoor or handle hits the wall. Its swing needs at least 2⅛″.
Model notes

The fit guide allows 3¾″. The spec drawing also marks 2⅛″ and 4¾″ at the open right door. The larger figure is the conservative fit. A tighter short-wall fit needs hinge-setback data.

SamsungRF31CG7400SRAAWon’t fitDoor or handle hits the wall. Its swing needs at least 1⅞″.
Model notes

The door projects 1⅞″. An older fit guide says 3¾″ along a wall. The model-specific drawing gives 4¼″ for the handle at 90°. A tighter short-wall fit needs hinge-setback data.

Measuring guide

Measure at the hinge.

Start at the metal case

Facing the fridge, measure the smallest horizontal gap from the right side of the case to the finished wall. Include projecting trim. Enter a decimal or fraction, such as 0.25, ¼ or 2 ⅛.

Find the wall’s front edge

Use Full wall when the wall continues beside the opened door and its handle. Use At or before hinge if the wall ends at or behind the pivot and nothing projects into the swing. Choose Partway / unsure for a short return beyond the hinge or an uncertain endpoint.

Read the drawing before ordering

Verdicts cover the original handle and the right door opening to 90°. A model can also fail its specified side installation gap. Check the opening width and height, the left, rear and top clearances, and drawer removal separately. Allow for wall finish and measuring tolerance at the published limits. Each model links to its manufacturer’s documentation.

Kitchen field guides